Reyds.Heat pumps · Boilers · Steam

Ruimsig · West Rand

Ice Machine Relocation in Ruimsig

Ice Machine Relocation in Ruimsig, West Rand. Safe decommission, move and recommission of ice plant.

Relocations are the point at which siting mistakes get corrected: clearances, ambient, drain fall and water pressure. We isolate, drain, move, reconnect and recommission with the output verified in the new position.

The ice plant here is mostly estate clubhouses, guest houses, small restaurants and private bars, so the work is weighted towards undercounter and small modular machines. West Rand attendance carries fuller van stock — inlet valves, pumps, thermostats and fan motors — because parts runs back to Johannesburg cost half a day.

Water in this part of Gauteng is moderately hard, so scale on evaporator plates, spray bars and float valves is the single most common reason output drifts below the plate rating. Condenser clearance and kitchen extract have as much effect on daily output as the refrigeration charge, so both are checked before any sealed-system work is quoted.

Area
Ruimsig, West Rand
Turnaround
Half to one day per machine.
Call
069 268 0988

Ruimsig

Scope of work

  • Isolation, drain-down and prep
  • Safe transport and positioning
  • Water, drain and electrical reconnection
  • Levelling and clearance correction
  • Recommissioning and output test
  • Sanitise before return to service

When to call

Symptoms we see locally

  • Kitchen refit or move
  • Machine in a poorly ventilated position
  • Drain with insufficient fall

Technical detail

Plant specification

Machine typesCube, half-dice, full-dice, flake, nugget, tube, block and gourmet ice
ConfigurationsSelf-contained undercounter, modular head on bin, remote condenser, split plant
Condenser typesAir-cooled, water-cooled and remote air-cooled
RefrigerantsR134a, R404A, R448A, R449A, R290 and R600a depending on model and age
Output range20 kg/24 h undercounter through to 1 000 kg+/24 h modular and flake plant
Water supplyPotable cold feed, typically 1–6 bar, with filtration and softening where hardness demands
Electrical230 V single phase on smaller plant; 400 V three phase on large modular and flake machines
ControlThermostatic or electronic harvest control, bin level probes and timed purge cycles
Local contextEstate housing with heat pump hot water and pool heating.

FAQs

Frequently asked questions

Do you attend ice machine relocation in Ruimsig?

Yes. Ruimsig falls inside our standard West Rand coverage. West Rand attendance carries fuller van stock — inlet valves, pumps, thermostats and fan motors — because parts runs back to Johannesburg cost half a day. Call 069 268 0988 to book an attendance slot.

How long does ice machine relocation take?

Half to one day per machine.

Which machines do you work on in Ruimsig?

Everything from self-contained undercounter machines to modular heads on bins and production plant, including modular ice machines & bins, water-cooled ice machines, remote condenser ice machines. The ice plant here is mostly estate clubhouses, guest houses, small restaurants and private bars, so the work is weighted towards undercounter and small modular machines.

Which brands are covered?

We service all common commercial makes, including KTI-Plersch, Hoshizaki, Manitowoc, Scotsman, and can source the usual wear parts — inlet valves, float valves, pumps, spray bars, thermostats and fan motors.

What is included in the price?

The visit covers isolation, drain-down and prep, safe transport and positioning, water, drain and electrical reconnection and a written record of findings. Parts are quoted before fitting unless you have authorised a repair limit.

A related problem is "Ice Machine Not Harvesting" — is that covered?

Ice forms on the plate but never releases into the bin. That is diagnosed on the same visit, and the fault page for Ruimsig sets out the usual causes and how we test for them.

Ice Machine Relocation in Ruimsig

Pool and domestic heat pumps serviced in the same visit.