Reyds.Heat pumps · Boilers · Steam

Silverton · Pretoria

Ice Machine Relocation in Silverton

Ice Machine Relocation in Silverton, Pretoria. Safe decommission, move and recommission of ice plant.

Relocations are the point at which siting mistakes get corrected: clearances, ambient, drain fall and water pressure. We isolate, drain, move, reconnect and recommission with the output verified in the new position.

The installed base here is production duty — flake, tube and block plant tied into food processing, cold rooms and process cooling — which means three-phase machines and planned rather than reactive maintenance. Pretoria and surrounds are covered on planned routes, with ice-plant breakdowns slotted into the nearest run.

Filtration sized on measured hardness and throughput is the cheapest protection available for an ice machine's water circuit and pump. Peak demand normally lands in a two-hour service window, so storage volume matters as much as production per 24 hours.

Area
Silverton, Pretoria
Turnaround
Half to one day per machine.
Call
069 268 0988

Silverton

Scope of work

  • Isolation, drain-down and prep
  • Safe transport and positioning
  • Water, drain and electrical reconnection
  • Levelling and clearance correction
  • Recommissioning and output test
  • Sanitise before return to service

When to call

Symptoms we see locally

  • Kitchen refit or move
  • Machine in a poorly ventilated position
  • Drain with insufficient fall

Technical detail

Plant specification

Machine typesCube, half-dice, full-dice, flake, nugget, tube, block and gourmet ice
ConfigurationsSelf-contained undercounter, modular head on bin, remote condenser, split plant
Condenser typesAir-cooled, water-cooled and remote air-cooled
RefrigerantsR134a, R404A, R448A, R449A, R290 and R600a depending on model and age
Output range20 kg/24 h undercounter through to 1 000 kg+/24 h modular and flake plant
Water supplyPotable cold feed, typically 1–6 bar, with filtration and softening where hardness demands
Electrical230 V single phase on smaller plant; 400 V three phase on large modular and flake machines
ControlThermostatic or electronic harvest control, bin level probes and timed purge cycles
Local contextIndustrial and manufacturing area with boiler plant and process heating.

FAQs

Frequently asked questions

Do you attend ice machine relocation in Silverton?

Yes. Silverton falls inside our standard Pretoria coverage. Pretoria and surrounds are covered on planned routes, with ice-plant breakdowns slotted into the nearest run. Call 069 268 0988 to book an attendance slot.

How long does ice machine relocation take?

Half to one day per machine.

Which machines do you work on in Silverton?

Everything from self-contained undercounter machines to modular heads on bins and production plant, including gourmet & ball ice machines, undercounter ice machines, modular ice machines & bins. The installed base here is production duty — flake, tube and block plant tied into food processing, cold rooms and process cooling — which means three-phase machines and planned rather than reactive maintenance.

Which brands are covered?

We service all common commercial makes, including Electrolux Professional, Whirlpool Commercial, KTI-Plersch, Hoshizaki, and can source the usual wear parts — inlet valves, float valves, pumps, spray bars, thermostats and fan motors.

What is included in the price?

The visit covers isolation, drain-down and prep, safe transport and positioning, water, drain and electrical reconnection and a written record of findings. Parts are quoted before fitting unless you have authorised a repair limit.

A related problem is "Ice Machine Freezing Up" — is that covered?

Ice builds on the suction line, plate or in the bin, jamming the machine. That is diagnosed on the same visit, and the fault page for Silverton sets out the usual causes and how we test for them.

Ice Machine Relocation in Silverton

Boiler efficiency baselining offered alongside repairs.